.jpg "日本閥天RD-14H減壓閥")
商鋪名稱：上海典昭閥業有限公司
聯系人：黃經理（先生）
聯系手機：
固定電話：
企業郵箱：Dzvalve@Foxmail.com
聯系地址：上海市松江區洞涇工業區洞寧路655弄181A
郵編：201100
聯系我時，請說是在五金機電網上看到的，謝謝！
商品詳情
| 產品參數 | |||
|---|---|---|---|
| 品牌 | 日本閥天 | ||
| 連接形式 | 法蘭 | ||
| 適用介質 | 油品 | ||
| 3C閥門類別 | 工業 | ||
| 公稱通徑 | 20-150 | ||
| 結構形式 | 活塞式 | ||
| 壓力環境 | 低壓 | ||
| 工作溫度 | 高溫 | ||
| 標準 | 日標 | ||
| 流動方向 | 單向 | ||
| 驅動方式 | 脈沖 | ||
| 零部件及配件 | 閥體 | ||
| 形態 | 膨脹式 | ||
| 類型(通道位置) | 直通式 | ||
| 規格 | 20-150 | ||
| 可售賣地 | 全國 | ||
| 材質 | 鑄鐵 | ||
| 型號 | RD-14H | ||
| 日本閥天RD-14H減壓閥詳細描述：RD-14H?valve?is?suitable?for:?oil,?pressure?1.0Mpa?following?caliber?range:?20-150mm?Suitable?temperature:?5-90?℃?Body?material:?cast?iron?valves?day?Japan?RD-14H?is?by?adjusting?the?valve,?the?inlet?pressure?is?reduced?to?the?outlet?pressure?of?a?need,?and?rely?on?the?energy?of?the?medium?itself,?so?that?automatically?maintain?a?stable?outlet?pressure?valve.RD-14H減壓閥適用于：壓力1.0Mpa以下的油品，口徑范圍：20-150mm?適用溫度：5-90℃?閥體材質為：鑄鐵?日本閥天RD-14H減壓閥是通過調節，將進口壓力減至某一需要的出口壓力，并依靠介質本身的能量，使出口壓力自動保持穩定的閥門。Operation:1,?closed?gate?valve?before?the?open?gate?valve?after?low?pressure?downstream?manufacturing?environment;2,?the?adjusting?screw?counterclockwise?rotation?to?the?uppermost?position?(relative?to?the?minimum?outlet?pressure),?and?then?close?the?valve?after?the?valve;3.?Slowly?open?the?gate?valve?to?fully?open?before;4.?Slowly?turn?adjustment?screw?clockwise,?the?pressure?is?adjusted?to?the?desired?outlet?pressure?(gauge?pressure?in?the?valve?prevail);?adjusted,?the?lockNut,?open?the?valve?gate?valve;5,?such?as?export?when?adjusting?the?pressure?higher?than?the?set?pressure,?must?start?from?the?first?step?to?re-adjust,?which?can?only?tune?from?low?to?high?pressure.日本閥天RD-14H減壓閥操作方式：1、關閉減壓閥前的閘閥，開啟減壓閥后的閘閥，制造下游低壓環境；2、將調節螺釘按逆時針旋轉至最上位置（相對最低出口壓力），然后關閉減壓閥后閘閥；3、慢慢開啟減壓閥前的閘閥至全開；4、順時針慢慢旋轉調節螺釘，將出口壓力調至所需要的壓力（以閥后表壓為準）；調整好后，將鎖緊螺母鎖緊，打開減壓閥后閘閥；5、如在調整時出口壓力高于設定壓力，須從步開始重新調整，即只能從低壓向高壓調。 |
